Black screen touch glass and LCD assembled to Darkmoon Wiko

PMFR6148

New

Touch glass screen and LCD assembled black Wiko Darkmoon.

More details

This product is no longer in stock

16,32 € tax incl.

Data sheet

Pre-gluing of the glass: No: Not systematic: It is necessary either to recover the old one, or to buy adhesive "quarter rolls 2mm"
For what type of breakdown? Typical LCD or touch-sensitive problems: Display fault, black screen, image with faults. Touch problem, touch that does not respond or wrong. Screen that stays fixed on the logo at startup. Impossible to type or type anything.

More info

Change the full screen of a Darkmoon Wiko

This full screen to Wiko Darkmoon consists of a < stRong >e screen LCD + touch glass. Pre-assembled at the factory, this high quality screen is offered so that you can proceed to the < strong >replacing the screen of your Darkmoon Wiko yourself < /stRong >. Our products are all carefully selected and tested by our technicians provide you with the best quality.
The tutorial at your disposal is all very detailed. It is directed by professionals for repair. More than the ecreplacement-to Wiko Darkmoon ranThis operation requires some special tools. You will find all you need in our < stRong >set of tools Wiko < /.strong >.  

Remove the back cover of your Darkmoon Wiko < /.H3 >

  • Before proceeding with disassembly of your Darkmoon Wiko, it is important for safety reasons, turn off voltage. < SPyear >
  • The help of a spatula nylon, unclip the cover top of the phone. Then proceed with its withdrawal.
  • Use yourto unclip plastic spatula the top cover of your Darkmoon Wiko . You can now drop. < /span >
  • Reuse your plastic spatula to remove the < strong >lower cache and drop it.../ span >
  • Unscrew the 3 Phillips head screws that hold the back cover of your Darkmoon Wiko .
  • Still using your plastic spatula, gently unclip the hull rear. To do this, drag your between the back cover and the rest of the Smartphone, and then drag it on contour. < SPyear >
  • This is! You can finally < strong >remove the back cover of your Darkmoon Wiko < /.strong >.

Remove the battery from your Darkmoon Wiko

  • Use a Phillips screwdriver to unscrew the 5 screws that hold the plastic of the motherboard cache. Once unscrewed, use your pliers to remove.
  • Disconnect the battery from the motherboard by levering on the battery connector. < /span >
  • Gently remove the < strong >battery your Darkmoon Wiko by levering using your spatula. Do not hard pullthe battery in order not to damage them. < /span >
  • You can now remove the battery from its location.

Drop the motherboard of your Darkmoon Wiko < /.H3 >

  • Disconnect the coaxial cable of the GSM antenna using your spatula plastic.
  • Also disconnect the liaison of the management card slick. < /span >
  • Still using your plastic spatula, disconnect the water of the < strNGO >rear camera in your Darkmoon Wiko < /.strong >. Once disconnected, you can drop the camera back through your precision pliers.
  • Use your spatula to disconnect the water of the screen LCD. < /span >
  • Disconnect the water of the touch screen using your spatula plastic again. < /span >
  • Disconnect the water of the front camera of your Darkmoon Wiko .
  • Use your spatula to take off and remove the front camera of its location. < SPyear >
  • Use your screwdriver to unscrew the screws securing the motherboard. < /span >
  • Now carefully lift the motherboard of your Darkmoon Wiko in order to deposit it.../ span >
  • Using your precision pliers, remove the tablecloth of binding of the card as shown on the video.
  • Carefully place the < strong >motherboard of your Darkmoon Wiko .

File management of the bottom card./H3 >

  • Reuse your pliers to remove the antenna of the GPS. < /span >
  • Once thethe your Darkmoon Wiko GPS antenna disassembled, remove the rubber from the brightness and proximity sensor < SPyear >
  • Remove it gently.strong >internal speaker of your Darkmoon Wiko using your plastic spatula.
  • Using a Phillips screwdriver, unscrew the two screws that hold the block your Darkmoon Wiko speaker.
  • PRY gently using your spatula to take off the antenna GSM card
  • Still use your precision pliers to enter the GSM antenna coaxial cable then drop all < stroNG >coaxial cable + antenna GSM your Wiko Darkmoon card .
  • Gently take off the tablecloth of binding of map management from the bottom of the chassis of your Smartphone.
  • Dislodge the vibrator from its location without removing it completely. Be careful not to remove it completely because it is connected to the Board with two sons.
  • Now, use your plastic spatula to place the management of the bottom card.../ span >
  • Remove the rubber from the microphone using your precision clamp. Take off then the two tablecloths the < strong >map of the lighting of the buttons on the screen at the bottom of your Darkmoon Wiko .
  • Once disconnected, you can drop the card of the lighting of the buttons on the screen. This is! The < strong>management of the bottom of your Wiko Darkmoon card is now ready to be filed.

Replace the full screen of your Darkmoon Wiko

  • Gently peel off the tablecloth of the power and volume buttons using your spatula in plastic.
  • THEfull screen of your Darkmoon Wiko is finally dismantled. You can replace it with another brand new and go to reassembly. < /span >
  • For back up your Darkmoon Wiko, we recommend that you replicate the steps of this tutorial in the reverse order
 

Delivery Date

Order before 14 h

for delivery between 30/03 and the 02/04/24

Approximate date using Suivi GRATUIT moreInfo
Close